The following includes messages from NE3200-NW.LAN.
025: You cannot load MSM31X on a NetWare 3.10 server.
Source:
NE3200-NW.LAN
026: On a NetWare 3.11 server, you must load LSLENH.NLM before you load MSM31X.NLM.
Source:
NE3200-NW.LAN
050: The board cannot be found.
Source:
NE3200-NW.LAN
051: Board RAM failed the memory test.
Source:
NE3200-NW.LAN
067: The group bit in the node address override was cleared.
Source:
NE3200-NW.LAN
068: The local bit in the node address override was set.
Source:
NE3200-NW.LAN
070: The board has failed.
Source:
NE3200-NW.LAN
Possible Cause:
Firmware was downloaded to the network board, but the network board did not accept commands.
Action:
Check the network board and other hardware. If necessary, replace the network board.
071: The matching virtual adapter could not be found.
Source:
NE3200-NW.LAN
072: A resource tag is unavailable.
Source:
NE3200-NW.LAN
073: Unable to allocate memory.
Source:
NE3200-NW.LAN
074: The hardware interrupt cannot be set.
Source:
NE3200-NW.LAN
075: The MLID cannot be registered with the LSL.
Source:
NE3200-NW.LAN
076: The polling procedure cannot be added.
Source:
NE3200-NW.LAN
077: The event notification routine cannot be registered.
Source:
NE3200-NW.LAN
078: The firmware file cannot be read.
Source:
NE3200-NW.LAN
Possible Cause:
NetWare could not read from the .LAN file on the disk from which it was loaded.
Action:
Check for hardware problems with the disk from which the LAN driver was loaded.
079: The MLID did not initialize MSMTxFreeCount.
Source:
NE3200-NW.LAN
086: The driver parameter block is too small.
Source:
NE3200-NW.LAN
087: The media parameter block is too small.
Source:
NE3200-NW.LAN
091: The hardware configuration conflicts.
Source:
NE3200-NW.LAN
092: Cannot schedule AES without an HSM routine.
Source:
NE3200-NW.LAN
093: Cannot schedule interrupt time call back without an HSM routine.
Source:
NE3200-NW.LAN
094: Cannot set hardware interrupt without an HSM routine.
Source:
NE3200-NW.LAN
095: Cannot add polling without an HSM routine.
Source:
NE3200-NW.LAN
236: No RCBs are available for the board to initialize.
Source:
NE3200-NW.LAN
Possible Cause:
The computer could not initially allocate Receive Control Blocks for this network board
Action:
Set the minimum packet receive buffers (in STARTUP.NCF) to a higher number.
237: The firmware cannot be initialized.
Source:
NE3200-NW.LAN
Possible Cause:
The network board did not inform the host that it was alive after it was reset.
Action:
Check the network board and other hardware. If necessary, replace the network board.
238: The firmware cannot be started.
Source:
NE3200-NW.LAN
Possible Cause:
The network board passed the self-test after being reset, but it did not download the firmware
Action:
Make sure the network board is in a bus-master compatible slot. You may need to replace the board.
241: The board’s ROM has checksum errors.
Source:
NE3200-NW.LAN
Possible Cause:
The network board failed the self-test. A ROM checksum error occurred.
Action:
Check the network board and other hardware. If necessary, replace the network board.